Cleaning & Maintaining Grout


Wine spilled on a tile floor with white grout.

Grout is everyone's least favorite part of tile, and with good reason. Many people have had bad experiences with stained, dirty, mildewy grout in floors or showers, and would like to avoid those headaches with their new installations.

 

Fortunately, we're here to help make grout selection, cleaning, and maintenance easy and stress-free.

Choosing grout for a new project? Figure out what's important to you.


Low Maintenance

Invest in a high-quality grout that never requires sealing, such as QuartzLock urethane grout or Fusion Pro single-component grout.

Less Expensive

If you want a less expensive option or are installing grout in an area with low wear and tear, consider a cement-based grout. Cementitious grout is porous and will need to be sealed. You will need to also purchase the color- and texture-matching caulking for any corners or transitional points (for example: between your tile floor and a wood floor), as cement-based grout is brittle and will crack if put in these areas.

Things to think about with Cement Grout


If you're installing cementitious grout with a tile that doesn't require sealing (a glossy glass mosaic set with a glazed porcelain tile, for example), we recommend using Grout Boost. Grout Boost is a liquid additive that you mix into your grout powder instead of water to provide a lifetime seal from the inside out.

 

If you are using cementitious grout with a natural stone, a glazed ceramic wall tile, or a polished porcelain, preseal your tiles to prevent the grout pigments from staining your tiles and to allow for easier clean-up after the grout is installed.

 

If you are not using a grout additive, you'll need to apply a sealer to your grout. Wait three days after you install your cement-based grout, and then seal it! Properly sealing your cement-based grout is the key to keeping it clean. A high quality, 15-year penetrating sealer will sink deep into the grout, coating the pores and adding a layer of protection from stains, dirt, and bacteria.

If you're cleaning up grout residue...


Urethane Grout

Blaze Urethane Grout Haze Cleaner

Work in small sections (no more than 10 square feet at a time) to reduce the risk of grout haze. Change your water bucket at least every 100 square feet to reduce the spread of residue, and make sure to wring out your sponge well so that you don't saturate your grout with water.

 

If you notice haze after your installation and initial clean up, we recommend using Blaze urethane grout haze remover within 24-48 hours of your installation to clean up any residue.

Fusion Pro

AquaKleen

Following installation, wipe up the grout residue with a damp sponge and clean water.

 

If you return the next day and notice grout haze, try lightly buffing the haze with a clean, dry cloth to remove it. If there is still some stubborn grout residue left over, it can be removed with any pH-neutral cleaner. We recommend Aqua Kleen for smaller installations and Concentrated Tile & Stone Cleaner for areas over 200 square feet.

Epoxy Grout

Jasco and Miracle brand epoxy removers

Begin clean up within the manufacturer's recommended time frame with clean, cool water and a non-abrasive scrub pad. Depending upon the epoxy brand, you have between 12 and 24 hours to thoroughly clean up any haze or residue before it dries to a stubborn, rubbery residue.

 

If you've followed the basic cleaning instructions and still have haze or residue, we recommend using either Miracle Epoxy Grout Film Remover 800 or Jasco Premium Paint and Epoxy Remover.

Cementitious Grout

Grout Haze Clean-Up

Wipe up most of the residue with a damp sponge and clean water just after the grout is installed. Don't worry about getting all of the residue at this step, as you may over-clean your grout and remove the pigments. Add Grout Haze Clean-Up to your water during clean up for best results.

 

After a few hours, the grout residue will have dried to a dusty state that is easily wiped off with a dry cloth. Any solid pieces or thicker residue can be scrubbed off with water and a non-abrasive nylon scrub pad. For particularly stubborn residue, we recommend Aqua Mix's Grout Haze Clean-Up.

 

If you used Grout Boost in your grout, you may notice a film on the surface of your grout joints. Use Aqua Mix's Grout Haze Clean-Up to remove the film.

If you need to clean dirty old grout...


Grout Deep Clean

We recommend starting with Grout Deep Clean. This powerful cleaner is specifically designed to remove grease, food stains, soap scum, hard water deposits, dirt, and soil from grout without damaging your tile or natural stone.

 

You will need to reseal your grout and stone after using this product. Visit our Sealer page for a list of recommended sealers. 

There are black stains in my grout and/or caulking, and my cleaning products haven't been able to get rid of it.

You most likely have a mold or mildew problem that is coming from behind your grout and/or caulking. There are several possible causes: the grout did not have enough time to cure before it was sealed, the shower was wet when the caulking went in (sealing the moisture in), or there is a leak in the shower and mildew is growing in the materials behind your tile.

 

If the mildew can not be killed through topical methods, you may need to remove your grout and some tiles to investigate the source of the mildew. If there is moisture in the framework of your house, this could lead to serious mold growth and structural damage.

Killing Mold & Mildew on the Surface of Grout

Grout Deep Clean

For grout with mold, we recommend Heavy Duty Tile & Grout Cleaner. This alkaline cleaner will neutralize and kill the mold. 


You will need to reseal your grout and stone after using this product. Visit our Sealer page for a list of recommended sealers. 

Professional Grout Cleaning & Repair


Grout Pro

Jeff Meyer

425-890-9798

tile.repair@comcast.net

If you want to change the color of your grout...


You can remove your old grout and regrout; or, if your grout is in good condition, you can use a grout colorant system. This process cleans and seals your grout in addition to permanently changing the color. Read more about grout colorants

If you have cracked grout...


Grout cracks either because it was installed improperly or because it was not the correct material to use in your specific installation. See the examples below to find the cause and solution to your specific problem.

 

If your grout is sagging into the joint or if sunken holes appear, not enough grout was packed into the joints when it was first installed. Make sure the grout is clean and dry, then apply more grout to the sunken areas. NOTE: Cement-based grout's color can vary based upon the water-to-powder ratio, minerals in the water, humidity, and temperature. The grout patch may be slightly different in color than the original grout, even when grouted less than 24 hours apart. This is not an issue with color-consistant grouts (urethane or Fusion Pro, for example).

 

If your grout is cracking only on inside corners such as where a wall meets a bathtub or where a backsplash meets a countertop, then you need to remove it and replace it with color-matching caulking (siliconized latex for dry areas like backsplashes, 100% silicone for wet areas such as showers or tub surrounds). Cementitious grout is too brittle to go in corners where flex and movement may occur.

 

If non-sanded cement-based grout is installed in a grout joint exceeding 1/8" in width, it could shrink upon curing, separating itself from the tile and cracking. If this is your situation, remove your grout and replace it either with sanded cement-based grout or with a more flexible grout, such as urethane or Fusion Pro.

 

If your grout is separating from your tiles in several different areas, you could have a too much movement in your installation. This can be caused by a variety of reasons, including (but not limited to) an unstable underlayment or contraction/expansion of the tiles (more common in outdoor applications). Remove what grout remains and replace it with a highly-flexible grout, (urethane or Fusion Pro).

 

NOTE: if the problem is structural (e.g.: mold underneath the tile, the tile was improperly set, etc.), then no amount of re-grouting will fix it. You will have to remove the tile and fix the underlying problems, or risk more permanent structural damage.


Was this page helpful? Share it with a friend!